keeprite furnace codes

If you’re looking for help fixing your Keeprite furnace, look no further! Our comprehensive Keeprite furnace repair guide will explain common issues, provide troubleshooting tips, and show you how to read your model’s error codes.

CODE: LED flashes like a heartbeat
PROBLEM: Control has 24 VAC power
FIX: n/a

CODE: Two LED flashes
PROBLEM: Unit’s pressure switch didn’t open
FIX: Check for an obstruction in the pressure tubing

CODE: Three LED flashes
PROBLEM: Unit’s pressure switch didn’t close or reopened
FIX: Check for: excessive wind; proper vent size; defective inducer motor; defective pressure switch; inadequate combustion air supply; disconnected or obstructed pressure tubing; or restricted vent

CODE: Four LED flashes
PROBLEM: Limit circuit fault: either a limit or flame rollout is open
FIX: Check for: restricted vent; proper vent sizing; loose blower wheel; excessive wind; dirty air filter; or defective blower

CODE: Five LED flashes
PROBLEM: An abnormal flame proving signal, the flame is likely proved while the gas valve is de-energized
FIX: Check for a leaky gas valve or a gas valve that is stuck open

CODE: Six LED flashes
PROBLEM: Failure to ignite or the flame sensor was lost while running
FIX: Check for: an ungrounded flame sensor; defective hot surface ignitor; low inlet gas pressure; oxide buildup; manual valve shut off; control ground continuity; inadequate flame carryover; or rough ignition

CODE: Seven LED flashes
PROBLEM: Limit circuit lockout
FIX: A lockout will occur if the limit or flame rollout is open for longer than 3 minutes. Control will auto-reset after 3 hours

CODE: Eight LED flashes
PROBLEM: Gas heating lockout, control won’t auto-reset
FIX: Check for a miswired gas valve or a defective control valve

CODE: Ten LED flashes
PROBLEM: Polarity is reversed
FIX: Review instructions to correct polarity

CODE: 1 + 2
PROBLEM: The blower is on after power up
FIX: Occurs if the unit is powered up during a call for heat or opens while the blower is on delay

CODE: 6 + 1
PROBLEM: Ignition lockout
FIX: Control will auto-reset after 3 hours

CODE: LED is off
PROBLEM: Secondary voltage fuse is open
FIX: Check whether the door switch isn’t closed or for a short circuit

CODE: LED is on
PROBLEM: Control circuitry lockout
FIX: Will auto-reset after 1 hour

CODE: LED is solid
PROBLEM: Gas valve relay is stuck while open, flame sense circuit failure, or software-check error
FIX: Reset power to clear the lockout and then replace control if status code repeats itself

keeprite furnace codes

 


What Our Clients Are Saying About Us

I would recommend KDM for sure

July 10, 2020

Dan was very friendly and polite from the start. Did exactly the work that we talked about on the phone, and was very quick making a late evening call on a Sunday. Tested all the joints and even painted the gas lines. I would recommend him for sure.

Colin JacobsCourtice, ON

I would recommend KDM for any of the services they provide

July 10, 2020

I had a 2nd hand pool heater hooked up and needed help getting it fired up. So I contacted Dan at KDM to see if they could help and was pleased he could make it over within a couple of days. He checked out the gas piping for leaks and proceeded to analyze the components of the control system and determined a faulty pressure switch was likely preventing operation. I was able to source the part and Dan was able to make a 2nd call within a day to install and complete the job. So in summary, I would recommend KDM for any of the services they provide.

Douglas PattersonWhitby, Ontario

KDM was hired for the Installation and relocation of internal gas line

July 10, 2020

KDM was hired for the Installation and relocation of internal gas line for my basement finishing project.

Paul AlisonOshawa, Ontario

Daniel and Steve were amazing, very professional work and courteous

July 10, 2020

Daniel and Steve were amazing, very professional work and courteous….never dealt with more friendly and knowledgeable Hvac technicians.

Rajshar MahomesMarkham, Ontario

I would not hesitate to hire Daniel and his crew again

July 10, 2020

Asked for quotes on a A/C and furnace after 17 years when the A/C unit broke down. I contacted a few HVAC contractors including KDM. Daniel could not have been more helpful and responsive and after reviewing the quotes decided to hire him for the job. Could no have made a better choice. Daniel was patient and upfront and answered all my questions when asked. He upgraded my A/C unit for the same price after the original unit we agreed upon was back ordered. The crew came when they said they would an completed the installation in a timely and orderly fashion.

I would not hesitate to hire Daniel and his crew again. In fact he is coming back to deal with another issue I have next month!

Job well done.

Ian DavidPickering, Ontario

I definitely recommend KDM Home & gas for others

July 10, 2020

I was looking for someone who can do the gas line connection on a weekend and I found the right guys with KDM Home & Gas. Daniel came on Sunday morning to do the work. He installed the new gas line, connected the new gas stove, confirmed no leaks and ensured everything works fine. It was a really hot day outside but he did an excellent job.

.

RajeevAjax, Ontario

Everything was quick and efficient

July 10, 2020

Assessment happened on a holiday and work was completed the following day. Everything was quick and efficient.
Thanks Daniel.

Chris SouthamWhitby, Ontario